Reprogrammation clé de fiesta 2000

[Invité §gui451wk]

Bonjour à tous.

Je possède une Fiesta 1.8D Ghia de 2000 qui me contente avec ses 155.000 km.

Aujourd'hui la télécommande avec trois boutons (ouverture, fermeture, coffre) me lache bien que la pile soit encore bonne .

Après avoir lu pas mal de post, je crois comprendre que je dois reprogrammer ma télécommande. Par contre, impossible de trouver la procédure pour mon modèle.

Quelqu'un a-t-il la procédure qui m'éviterait d'aller chez Ford?

Merci d'avance

 

Guillaume

[Invité §Ane658xr]

J'ai une fiesta de 1997, et je me demande si cela se reprogramme de la même manière...

J'aurais pu scanné la page de mon livret si tel est le cas

[Invité §kil147EF]

Bonjour,

 

Je ne sais pas si mon modèle de fiesta est le même que le votre (modèle 98 1.25 zetec) mais j'ai un problème du genre.

 

Les premiers symptômes ont été que au lieu de biper 2 fois pour fermer (1er bip qui ferme et l'autre qui active le verrouillage de l'intèrieur je crois avec les clignotants qui s'allume et donc j'avais 2 bruits de moteur, un pour chaque bip) et bien je ne pouvais plus biper qu'une seule fois (qu'un seul bruit de moteur).

Puis un peu plus tard, plus rien la télécommande n'agissait plus.

 

Donc je me demande si il ne faut pas une reprogramation.

Je suis aller voir en magasin sur la revue technique, pour une reprogramation il faut mettre le contact en 1 puis 0 et le voyant est censé s'allumer mais j'ai essayé et rien, il clignote comme à l'habitude.

 

Quelqu'un a t'il déjà rencontré ce problème??

 

merci

[Invité §kil147EF]

J'ai changé la pile mais rien et c'est une 2 boutons par contre.

[Invité §lul003Ip]

Il me semble avoir lu dans la "notice" ou sur le forum je sais plus qu'il faut deux clés pour en programmer une troisième (si j'ai bien compris lol).

Sinon, moi j'ai fait faire une autre clé car la proprio ne m'en avait filé qu'une, et en plus du prix de la clé, j'ai payé env 70 pour la programation chez ford .. aie !

 

Edit : moi aussi ma fiesta est de 98, télécommande avec deux boutons

[Invité §kil147EF]

personne a fait une reprog de ses clefs sur fiesta?

[Invité §Ane658xr]

Bonjour,

Je serais demain chez moi, et je vous scannerais la page où ils indiques comment la programmer.

Je doit aussi tester, car on me la vendue avec des piles mortes, donc forcément...

[Invité §kil147EF]

Voici la méthodes qui a permis de résoudre mon problème pour une 2 boutons celle pour 3 boutons plus bas

 

 

2Boutons

 

You must first have two keys that open and start your Puma before you can code new keys

A maximum of 4 keys with radio frequency remote control can be programmed for your vehicle.

 

Programming the Central Locking

Kindly posted by Pumapeople member 19rick47 May 2008

You have coded the keys so that they all start the engine, it doesn't also code the central-locking when you do that sequence.

A different sequence is required to code to the central locking:

 

1. Turn the ignition switch from the OFF to the ON position four times within three seconds to enter the learning mode.

2. Turn the ignition switch to the OFF position. The central security module will remain in the learning mode for 20 seconds indicated by the LED in the instrument panel being illuminated continuously.

3. Press any button on the remote transmitter being programmed. When the signal from the remote transmitter, is accepted by the central security module, the LED will flash.

4. To program additional transmitters, repeat step 3, with a 2 second delay after the LED flashes.

5. To exit the learning mode, turn the ignition switch to the ON position. If no transmitter signal is received by the central security module for 20 seconds, the system will automatically exit the learning mode.

6. Test all the programmed transmitters, by activating and deactivating the locking functions. For further keys, follow 3.

 

 

As far as I understand it, after 2. you leave that ignition key in the OFF position and press any button on any of the remotes you want to programme to the central locking.

And remember what has previously been posted, "It doesn't always work first time".

 

Programming to Start the Puma

Kindly posted by Pumapeople member Midnight BlueMay 2007

 

1. Insert the first programmed key into the ignition lock cylinder and turn the lock cylinder from the OFF position to the RUN position (maintain ignition lock cylinder in the RUN position for one second).

2. Turn ignition lock cylinder to the OFF position and remove the first key from the ignition lock cylinder.

3. Within five seconds of turning the ignition lock cylinder to the OFF position, insert the second programmed ignition key into the ignition lock cylinder and turn the ignition lock from the OFF position to the RUN position (maintain the ignition lock cylinder in the RUN position for one second).

4. Turn the ignition lock cylinder to the OFF position and remove the second key from the lock cylinder.

5. Within ten seconds of turning the ignition lock cylinder to the OFF position, insert the unprogrammed ignition key (new key) into the lock cylinder and turn the lock cylinder from the OFF position to the RUN position (maintain the ignition lock cylinder in the RUN position for less than 5 seconds).

6. Check the new programmed key starts the engine. Turn the ignition key to the OFF position for five seconds then try to start vehicle with the new programmed key.

 

 

 

Reprogramme remote key (when remote not work or car not start

Kindly posted by Pumapeople member pumadub May 2006

 

here you go mate try this and remember to do all keys.....

 

1. Close all doors and fasten the safety belts to make sure conflicting chimes do not sound during programming.

2. Turn the ignition switch from position I to position II at least four times in six seconds.

3. Turn the ignition switch to position I.

4. The central security module (CSM) is now in the learning mode.

5. Press and hold one of the buttons on the remote transmitter until a chime sounds. This indicates a new transmitter code has successfully received.

6. After each successful programming, another 10 second learning mode is automatically entered, up to a maximum of four times.

7. To program additional transmitters, repeat step 5.

8. The system will leave the learning mode after the ignition switch is turned to position III, or if no new transmitter is programmed during the 10 seconds, or if four remote transmitters have been programmed.

 

 

 

Still got problems trying to reprogramme

Kindly posted by Pumapeople member kaney06 May 2006

if you have changed the battery and followed both programming procedure's and still nothing try unplugging the alarm module above the drivers side kick panel,this will also clear and reset the module(a little trick that FORD doo and charge load's)

and posted by Pumapeople member Boyband July 2007

 

* Open the Drivers Door

* Loosen off the Rubber Lining in the Front Bottom Corner

* Pull the Carpet Away in that Corner

 

 

Behind there will be a large connector block which is part of the alarm and locking system. Sometimes while performing a previously failed programming attempt it can scramble this block and disconnecting it and then re-connecting it for about 30secs will reset it.

 

3 boutons

 

 

You must first have two keys that open and start your Puma before you can code new keys

A maximum of 4 keys with radio frequency remote control can be programmed for your vehicle.

 

Programming the Central Locking

Kindly posted by Pumapeople member 19rick47 May 2008

You have coded the keys so that they all start the engine, it doesn't also code the central-locking when you do that sequence.

A different sequence is required to code to the central locking:

 

1. Turn the ignition switch from the OFF to the ON position four times within three seconds to enter the learning mode.

2. Turn the ignition switch to the OFF position. The central security module will remain in the learning mode for 20 seconds indicated by the LED in the instrument panel being illuminated continuously.

3. Press any button on the remote transmitter being programmed. When the signal from the remote transmitter, is accepted by the central security module, the LED will flash.

4. To program additional transmitters, repeat step 3, with a 2 second delay after the LED flashes.

5. To exit the learning mode, turn the ignition switch to the ON position. If no transmitter signal is received by the central security module for 20 seconds, the system will automatically exit the learning mode.

6. Test all the programmed transmitters, by activating and deactivating the locking functions. For further keys, follow 3.

 

 

As far as I understand it, after 2. you leave that ignition key in the OFF position and press any button on any of the remotes you want to programme to the central locking.

And remember what has previously been posted, "It doesn't always work first time".

 

Programming to Start the Puma

Kindly posted by Pumapeople member Midnight BlueMay 2007

 

1. Insert the first programmed key into the ignition lock cylinder and turn the lock cylinder from the OFF position to the RUN position (maintain ignition lock cylinder in the RUN position for one second).

2. Turn ignition lock cylinder to the OFF position and remove the first key from the ignition lock cylinder.

3. Within five seconds of turning the ignition lock cylinder to the OFF position, insert the second programmed ignition key into the ignition lock cylinder and turn the ignition lock from the OFF position to the RUN position (maintain the ignition lock cylinder in the RUN position for one second).

4. Turn the ignition lock cylinder to the OFF position and remove the second key from the lock cylinder.

5. Within ten seconds of turning the ignition lock cylinder to the OFF position, insert the unprogrammed ignition key (new key) into the lock cylinder and turn the lock cylinder from the OFF position to the RUN position (maintain the ignition lock cylinder in the RUN position for less than 5 seconds).

6. Check the new programmed key starts the engine. Turn the ignition key to the OFF position for five seconds then try to start vehicle with the new programmed key.

 

 

 

Reprogramme remote key (when remote not work or car not start

Kindly posted by Pumapeople member pumadub May 2006

 

here you go mate try this and remember to do all keys.....

 

1. Close all doors and fasten the safety belts to make sure conflicting chimes do not sound during programming.

2. Turn the ignition switch from position I to position II at least four times in six seconds.

3. Turn the ignition switch to position I.

4. The central security module (CSM) is now in the learning mode.

5. Press and hold one of the buttons on the remote transmitter until a chime sounds. This indicates a new transmitter code has successfully received.

6. After each successful programming, another 10 second learning mode is automatically entered, up to a maximum of four times.

7. To program additional transmitters, repeat step 5.

8. The system will leave the learning mode after the ignition switch is turned to position III, or if no new transmitter is programmed during the 10 seconds, or if four remote transmitters have been programmed.

 

 

 

Still got problems trying to reprogramme

Kindly posted by Pumapeople member kaney06 May 2006

if you have changed the battery and followed both programming procedure's and still nothing try unplugging the alarm module above the drivers side kick panel,this will also clear and reset the module(a little trick that FORD doo and charge load's)

and posted by Pumapeople member Boyband[]/b] July 2007

 

* Open the Drivers Door

* Loosen off the Rubber Lining in the Front Bottom Corner

* Pull the Carpet Away in that Corner

 

 

Behind there will be a large connector block which is part of the alarm and locking system. Sometimes while performing a previously failed programming attempt it can scramble this block and disconnecting it and then re-connecting it for about 30secs will reset it.

[Invité §kil147EF]

la méthode est pour une puma mais c'est en tout cas la même chose pour ma fiesta

 

En gros :

 

1er paragraphe : programmation nouvelle clef pour l'infrarouge de la centralisée

 

2eme : Programmation pour l'antidémarrage

 

3eme : quand l'infrarouge ne marche plus ou changement de pile

 

4eme Quand rien ne marche, il préconise un débranchement du boitier de centralisé (fiesta c'est au pied du passager à gauche derrière le cache plastique). ça fait un reset des codes infrarouges. Mais cela ne touche pas à l'antidémarrage, J'ai démarré normalement après.

 

J'ai fait les instruction du 4eme paragraphe car cette manip ne fonctionnait pas :

 

2. Turn the ignition switch to the OFF position. The central security module will remain in the learning mode for 20 seconds indicated by the LED in the instrument panel being illuminated continuously. === voyant qui ne s'allume pas continuellement pour dire que le boitier est en mode programmation

 

 

Voilà en espérant que ça en aide plus d'un

 

[Invité §lul003Ip]

en même temps, tout le monde n'est pas bilingue lol, peut être qu'une traduction en aiderait encore plus que ça !!

[Invité §Ane658xr]

Je prososais de scanner la page du bouquin de ma fiesta, mais le principal intéréssé n'est plus là